How to enable Caller ID for CO Line in panasonic ns300 epabx?

By -Dated-

You can enable Caller ID for CO Lines...

  • Login your Web Maintenance Console
  • Go to PBX Configuration
  • Expand Configuration
  • Click on Slot
  • Go to LCOT6
  • Click on Card Property
  • Change Caller ID Signaling FSK into DTMF
  • Change Caller ID (DTMF) Start Code-1 A into None
  • Change Caller ID (DTMF) Start Code-2 D into None
Caller ID

  • Go to again PBX Configuration
  • Expand CO & Incoming Call
  • Select DIL Table and Port Settings
  • Enable CLI Ring for DIL Day/Night



Comments

Post a Comment

Please do not enter spam link.

Popular posts from this blog

How to configure Panasonic NS300 by initial easy setup wizard?

By -Dated-
Image
We can configure Panasonic NS300 when we setup new device. you can fallow the below steps- Login EPABX with help of Browser and IP Address (192.168.0.101) User-  INSTALLER  in Capital Letter Password-  1234  (By Default) Click on  Install Enter your  Password Click on  Start Setup Wizard Set the  Time Zone  and  Date/Time Click on  Next Select the CO Access No  (Dial "0") Select  Numbering Plan Click on  Next Set the  Manager Extention Click on  Next Select the CO Dialing Mode  (DTMF) Click on  Next Configure  IP Address Click on  Next Click on  Finish
Read more

How to configure Externel and Internal call block in panasonic ns300 epabx?

By -Dated-
Image
External Call Block- We can configure external call block settings in panasonic ns300 epabx. From doing this we can block outgoing calls from extentions of specific CO(Trunk) line. We restrict the CO Lines for preventing calling. Login your  Web Maintenance Console Go to  PBX configuration Expand  System Expand  Class of Service Select External Call Block Go to TRG 01-16 Draw the Blue Square for blocking CO Lines Internal Call Block- We can configure internal call block settings in panasonic ns300 epabx. From doing this we can block calling between two extention.  Login your  Web Maintenance Console Go to  PBX configuration Expand  System Expand  Class of Service Select  Internal Call Block Go to COS 01-16 Note- 1- COS1 and COS2 can make calls to COS1, COS2, COS3, COS4, COS5 & COS6           2- COS3 and COS4 can make calls to COS1, COS2, COS3 & COS4 only. ...
Read more

Just 6 Important Basic Steps for configurartion Panasonic KX-TES824

By -Dated-
Image
You can configure Panasonic EPABX System KX-TES824 after fallow just few steps- Enter in programing mode then after you configure just 6 steps as given below- Steps-1 Enter the in programing mode Enter Code "000" Set the Date & Time according to Instructions Date & Time Setup[000] Steps-2 Enter the in programing mode Enter Code "009" Configure Extention Number as given below Plan in Note Extention Number Assigning[009] Note- Programeable number follow as below- Plan 1:   100-199 Plan 2:   100-499 Plan 3:   20-49 Steps-3 Enter the in programing mode Enter Code "121" Select "0" or "9" according you Automatic Line Access[121] Steps-4 Enter the in programing mode Enter Code "401" Select DTMF Dial Mode[401] Steps-5 Enter the in programing mode Enter Code "400" Select "Connect" for you CO Line Select "No Connect" for Blank CO Port ...
Read more

How to record and upload DISA or Greeting/Welcome message in panasonic ns300 epabx?

By -Dated-
Image
You can record DISA/Welcome message easily by KTS phone. 1- For Recording Your Message Go on KTS Phone Press SP-Phone Enter *361501 Display Wait Message then start timing in Second Start speaking for recording your Greeting Message Press Store      For Listen Playback ( Your Recorded Message) Press  SP-Phone Enter *362501 2- Uploading ( Your Recorded Message) Login your  Web Maintenance Console Click on  Maintenance Go to Utility Expand File Select Message File Transfer PC to PBX Click on Choose File Click on OK
Read more

How to configure DISA message in panasonic ns300 epabx?

By -Dated-
Image
DISA Message configuration in panasonic ns300- Step-1 Login your  Web Maintenance Console Go to PBX Configuration Expand  Optional Device Click on Voice Message Select  DISA System Go to Intercept when all DISA ports are busy- Select to AA-9 Go to Intercept when No Dial after DISA answers- Select to AA-9 Step-2 Go to DISA Message Enter the ICD Group or Call Landing Extention Number opposit DISA(501/502) according selection of DISA Intercept in Step-2 Step-3 Go to again  PBX Configuration Expand  Group Click on  Extention Hunting Group Type ICD Group Name Step-4 Go to again  PBX Configuration Expand  Group Click on Incomming Call Distribution Group Select Group Settings Click on Main Go to Distribution Method Set UCD opposit ICD Group Number Step-5 Go to again  PBX Configuration Expand  Group Click on  Incomming Call Distribution Group Select  Group Settings ...
Read more

How to configure Trunk Group for calling in panasonic ns300 epabx?

By -Dated-
Image
You can configure Trunk Group and manage you CO Lines according you. Step-1 Login your  Web Maintenance Console Go to  PBX configuration Expand Group Select  TRG Settings Go to  Main Select  Rotation in Line Hunting Order Step-2 Login your  Web Maintenance Console Go to  PBX configuration Expand  Group Select Local Access Priority Type the Trunk(CO) Name Step-3 Login your  Web Maintenance Console Go to  PBX configuration Expand CO & Incoming Call Select  CO Line Settings Type the Trunk(CO) Name Set the Trunk Group Number Step-4 Login your  Web Maintenance Console Go to  PBX configuration Expand  Group Select  TRG Settings Go to Hot PBX Access Code Set the "0" for your CO Lines Note- You can use Step-4 when you using verification code for calling and not able to dial call after pressing "0"
Read more

How to configure Biometric(Biomax) N-BM160W for online software?

By -Dated-
Image
Biomax N-BM160W Configuration Step-1 Press Menu Button Select Settings Press OK Select Network Press OK Go to Mode(1) Press OK Select WAN Press OK Go to WiFi(5) Select Yes Press OK Go to Search(8) Select WiFi SSID Press OK Enter WiFi   Password Press OK Go to Server IP(6) Enter Static IP Press OK Go to Server Port(7) Enter Port Number Press OK Press ESC Press OK (When prompt message Are You Sure Want to Save? ) Step-2 Login Your Smart Office Console(Hosted) Go to Device Management Click on Devices Click on Add New Device Then Enter Device Name and Short Name Enter Cloud ID in the place of Serial Number Enter IP Address  Click on Save
Read more

How to route all inbound and outbound emails through a specific email ID in G Suits admin console?

By -Dated-
Image
 Email Routing in G Suits- If we have G Suits email account and we want all users incoming and outgoing emails copy receives their manage or HOD then we can do it after creating email routing policy in gmail. Login you G Suits Admin Console Go to Apps Click on G Suits Click on Gmail   Go to Advanced Settings Select your Organization Unit and go to Routing Click on Configure Check on Inbound and Outbound Check on Add more recipient under Also deliver to Add Recipient Click on Save Again click on Save
Read more